Digital torque value readout

CW and CCW operation

Peak hold mode

Engineering units ( Nm , ft-lb , in-lb, kg-cm) selectable

Auto power off after about 5 minutes idle

Rechargeable batteries are compatible

The post Geratech
DTWB Series first appeared on EgeRate Elektronik.

For Analog Dynamometer series and Digital Dynamometer series

** Dynamometer tests for all kinds of commercial applications
** Force gauge test for your research and development
** Tension / Compression tests
** Insertion /Withdrawal tests
** Fracture test
** T-screw transfer
** Vertical and Horizontal Use

Dynamometer Test Stand Features:

The post Geratech
SLJ-B first appeared on EgeRate Elektronik.

The LDT can be used to locate leaks in

• pneumatic systems
• vacuum equipment
• valves and fittings
• steam pipes
• oxygen sockets in hospitals
• air conditioning systems in automotive vehicles
• Door and window seals of cars, pressurized containers, ships, trucks, buses, trains, airplanes etc.

For difficult to reach locations we offer a longer goose neck probe as well as a parabolic dish with integrated ultrasonic sensor and laser pointer. The integrated laser pointer makes it easy to trace leaks over distances from 20m to more than 100m for bigger leaks. The parabolic dish is made of transparent plastic, so that the leaks are easily visible. All incoming ultrasonic waves are reflected from the dish and focused at the ultrasonic receiver. Noise is ignored.

Complete Kit

The LDT is supplied as a complete kit with 110mm probe, pin-point detection probe, headphones and calibration certificate in a fitted carrying case.

The post LDT
Ultrasonic Leak Detector first appeared on EgeRate Elektronik.

5 Models Available:
SPG: Integrated Probe, 500 micron / 20 mil range, 60° angle
SPG-S: Cabled Probe, 500 micron / 20 mil range, 60° angle
SPG-OS: Cabled Probe, for Convex Surfaces, 500 micron / 20 mil range, 60° angle
SPG-CS: Cabled Probe, for Textured Coatings, 1500 micron / 60 mil range, 60° angle
SPG-TS: Cabled Probe, for Concrete, 6 mm / 250 mill range, 60° angle

Conforms to ASTMD4417-B, ASTM D8271 (SPG TS only), AS 3894.5-C (with optional 30° tip), U.S.Navy NSI 009-32, Navy NAVSEA 009-32, US Navy NAVSEA PPI 63101-000, SSPC PA 17, SANS 5772, and others. Conforms to ASTM D4417-B, AS 3894.5-C (with optional 30° tip angle), U.S. Navy NSI 009-32, SANS 5772 and others.

The post Positector SPG
Surface Profile Gauge first appeared on EgeRate Elektronik.

The cross cut testers of the SecoTest series consist of a sturdy holder for the six-edge multi cutting blade and a rotatable non-slip grip, which prevents the multi cutting blade from canting.

To ensure that this procedure is repeatable, put the test object through a suitable conditioning process (see DIN EN ISO 2409, section 6); while testing at construction sites make a note of the ambient conditions in the test report.

The procedure defined by ISO 4642 can be employed to measure adhesiveness.

Complete Kit

The SecoTest includes:

• SecoTest
• Allen key for changing the multi cutting blade
• Magnifier
• Brush
• Short operating instructions
• Works Certificate
• Plastic carrying case

Blades are sold separately

The post SecoTest
Cross Hatch Cutter for ISO 2409 and ... first appeared on EgeRate Elektronik.

The AT-A is features an environmentally sealed enclosure. It is weatherproof, dustproof and shockproof. Meeting or exceeding IP65 rating.

Touch Screen Display

Use the touch screen to interact with menu options. Swipe horizontally to navigate between views or vertically to move between batch readings. Alternatively, the keypad can be used for navigation and selection.

User adjustable dolly size, pull rate, pull limit and hold time.

Batch summary provides an at-a-glance review of test results.

View test parameters and reading results. Reading is recorded as pass or fail based on set test parameters. The pass/fail results can be revised.

Notes can be added for each reading.

Include a note for a batch (group) of readings.

Record the nature of failure – cohesive, adhesive and glue failures.

Recording the Nature of the Fracture

Upon completion of a pull-off test, the dolly and coated surface should be examined. In addition to pull-off force, many National and International standards such as ASTM D4541 and ISO 4624 require the nature of the fracture to be recorded.

• Cohesive fracture: fracture occurs within a coating layer (same coating on dolly face and coated surface).
• Adhesive fracture: fracture occurs at the interface between layers (coating on dolly face differs from surface).
• Glue failure: visible separation of the glue from itself, the coating or dolly (no coating visible on the dolly face).

The cohesive and adhesive fracture visual analysis can be recorded using the PosiTest AT-A’s keypad or touch screen display. Alternatively, the information can be reported using the PosiTector App.

Fractures are visually estimated and recorded as a percent of each. The two layer example below illustrates a cohesive fracture within coating layer 1 and layer 2 (visually estimated at 50% each). Recorded results are included in reports.

Examples

(based on above five layer illustration)

100% cohesive fracture at D/E coating interface (layer 3/layer 4)

100% cohesive fracture at D/E coating interface (layer 3/layer 4)

70% cohesive failure within layer 1; 30% cohesive within layer 2

70% cohesive failure within layer 1; 30% cohesive within layer 2

Complete Kit

The PosiTest AT kits come complete with Automatic Adhesion Tester, built-in rechargeable NiMH battery with charger, dollies, abrasive pad, cutting tool, glue with mixing sticks and palettes, cotton swabs, USB cable, PosiSoft Software, instruction booklet and video, shoulder strap, Certificate of Calibration traceable to NIST, two-year warranty, and a sturdy, lightweight carrying case.

The post PosiTest AT-A
Automatic Adhesion Tester first appeared on EgeRate Elektronik.

The AT-M features an environmentally sealed enclosure. It is weatherproof, dustproof and shockproof. Meeting or exceeding IP65 rating.

Complete Kit

The PosiTest AT kits come complete with Manual Adhesion Tester, built-in rechargeable NiMH battery with charger, dollies, abrasive pad, cutting tool, glue with mixing sticks and palettes, cotton swabs, USB cable, PosiSoft Software, instruction booklet and video, shoulder strap, Certificate of Calibration traceable to NIST, two-year warranty, and a sturdy, lightweight carrying case.

The post PosiTest AT-M
Manual Pull-Off Adhesion Tester first appeared on EgeRate Elektronik.

Additional probes & Transducers are optionally available where regular checks need to be made from fixed Transducers attached to machine, this method provides more accurate & consistent results.

The post VIBCHECK
Portable Vibration Meter according t... first appeared on EgeRate Elektronik.

In addition to standard approaches, the MK-21uniquely checks machinery condition, in the Diagnostic mode, without reference to a chart … as easy as reading a, bb, ccc and dddd on the display – where a = Quite Good (Zone A), bb = Good (Zone B), ccc = Poor (Zone C) and dddd = Bad (Zone D).

Condition Zones A,B,C & D cover those vibration velocity ranges noted in ISO 10816.

		Low Range	HI Range
Measuring Range	ACC	0.0 ~ 20.0 m/s²	0 ~ 200 m/s²
	ACCP	0.0 ~ 20.0 m/s²	0 ~ 200 m/s²
	VEL	0.0 ~ 20.0 mm/s	0 ~ 200 mm/s
	DISP	0 ~ 200 µm	0 ~ 1990 µm
Frequency Range	ACC	1k ~ 20kHz
	ACCP	1k ~ 20kHz
	VEL	10 ~ 1kHz
	DISP	10 ~ 1kHz

Complete Kit

The MK-21 is supplied as a complete kit with the gauge and wrist strap, probe and cable assembly, batteries and instruction manual — all supplied in a fitted, hard plastic carrying.

The post MK-21
Vibration Meter first appeared on EgeRate Elektronik.

The post BCS
Electronic Crane Scale first appeared on EgeRate Elektronik.